Kabel

SIP-4 2x16 is a self-supporting insulated wire (Type-4) - 2 by 16 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.

SIP-3 1x240-20 is a self-supporting insulated wire (Type-3) - 1 by 240 mm2, with steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

SIP-2 3x70+1x70 is a self-supporting insulated wire (Type-2) - 3 by 70 mm2 + 1 by 75 mm2, with aluminum and steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

SIP-4 4x120 is a self-supporting insulated wire (Type-4) - 4 by 120 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.

SIP-2 3x50+1x50 is a self-supporting insulated wire (Type-2) - 3 by 50 mm2 + 1 by 50 mm2, with aluminum and steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

SIP-2 3x185+1x95 is a self-supporting insulated wire (Type-2) - 3 by 185 mm2 + 1 by 95 mm2, with aluminum and steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

The cables are designed for fixed connection to electrical appliances, apparatuses, terminal assemblies of electrical switchgear with rated alternating voltage up to 660 V frequency up to 100 Hz or constant voltage up to 1000 V. Cables are used for laying outdoors, in rooms, channels, tunnels, in the ground (trenches) in an aggressive environment, in places exposed to stray currents, if the cables are not subjected to significant tensile forces and if there is a risk of mechanical damage during operation.

SIP-3 1x35-35 is a self-supporting insulated wire (Type-3) - 1 by 35 mm2, with steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

KVBBSHVNG 14x1.5 is an abbreviated marking of an armored control cable with 14 copper cores with a cross section of 1.5 square millimeters, insulated and coated with polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

SIP-2 3x70+1x95 is a self-supporting insulated wire (Type-2) - 3 by 70 mm2 + 1 by 95 mm2, with aluminum and steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

SIP-3 1x25-35 is a self-supporting insulated wire (Type-3) - 1 by 25 mm2, with steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

KVBBSHVNG 27x2.5 is an abbreviated marking of an armored control cable with 27 copper cores with a cross section of 2.5 square millimeters, insulated and coated with polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

SIP-3 1x70-20 is a self-supporting insulated wire (Type-3) - 1 by 70 mm2, with steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

The cables are designed for fixed connection to electrical appliances, apparatuses, terminal assemblies of electrical switchgear with rated alternating voltage up to 660 V frequency up to 100 Hz or constant voltage up to 1000 V. Cables are used for laying outdoors, in rooms, channels, tunnels, in the ground (trenches) in an aggressive environment, in places exposed to stray currents, if the cables are not subjected to significant tensile forces and if there is a risk of mechanical damage during operation.

The cables are designed for fixed connection to electrical appliances, apparatuses, terminal assemblies of electrical switchgear with rated alternating voltage up to 660 V frequency up to 100 Hz or constant voltage up to 1000 V. Cables are used for laying outdoors, in rooms, channels, tunnels, in the ground (trenches) in an aggressive environment, in places exposed to stray currents, if the cables are not subjected to significant tensile forces and if there is a risk of mechanical damage during operation.

SIP-4 2x95 is a self-supporting insulated wire (Type-4) - 2 by 95 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.

SIP-4 4x50 is a self-supporting insulated wire (Type-4) - 4 by 50 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.

KVBBSHVNG 27x1.0 is an abbreviated marking of an armored control cable with 10 copper cores with a cross section of 1 square millimeters, insulated and sheathed in polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

KVBBSHVNG 19x1.5 is an abbreviated marking of an armored control cable with 19 copper cores with a cross section of 1.5 square millimeters, insulated and sheathed in polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

KVBBSHVNG 19x2.5 is an abbreviated marking of an armored control cable with 19 copper cores with a cross section of 2.5 square millimeters, insulated and sheathed in polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

SIP-3 1x120-35 is a self-supporting insulated wire (Type-3) - 1 by 120 mm2, with steel-aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

SIP-3 1x50-20 is a self-supporting insulated wire (Type-3) - 1 by 50 mm2, with steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

KVBBSHVNG 27x1.5 is an abbreviated marking of an armored control cable with 27 copper cores with a cross section of 1.5 square millimeters, insulated and sheathed in polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

SIP-3 1x120-20 is a self-supporting insulated wire (Type-3) - 1 by 120 mm2, with steel-aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

KVBBSHVNG 5x2.5 is an abbreviated marking of an armored control cable with 5 copper cores with a cross section of 2.5 square millimeters, insulated and coated with polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

SIP-4 2x35 is a self-supporting insulated wire (Type-4) - 2 by 35 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.

SIP-4 2x70 is a self-supporting insulated wire (Type-4) - 2 by 70 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.

SIP-4 4x16 is a self-supporting insulated wire (Type-4) - 4 by 16 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.

SIP-2 3x35+1x50 is a self-supporting insulated wire (Type-2) - 3 by 35 mm2 + 1 by 50 mm2, with aluminum and steel-aluminum cores covered with insulation from light-stabilized cross-linked polyethylene. This wire is intended for use in overhead power transmission lines (power lines) with suspension on supports or facades of buildings and structures.

SIP-4 2x25 is a self-supporting insulated wire (Type-4) - 2 by 25 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.