Провод

The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz.

Signal-blocking cables are designed for electrical alarm systems, centralization and blocking, fire alarm and automation. They are used for single laying in rooms, dry channels and tunnels, in an aggressive environment in the absence of mechanical influences on the cable.

VVGng(A) 3x6ok+1x4ok(N) - 1 is a power flat cable, with a copper core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz. For laying without limiting the level difference along the laying route, including on vertical sections.

KVBBSHVNG(A)-LS 27x0.75 is an abbreviated marking of an armored control cable with 27 copper cores with a cross section of 0.75 square millimeters, insulated and sheathed in polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

The cable is designed for operation in subscriber access networks in the frequency range up to 2048 kHz and the organization of lines on distribution telecommunication networks from the terminal device to the subscriber and sealing by transmission systems with a rated voltage of remote power supply up to 225 V or 350 V AC with a frequency of 50 Hz, or voltage up to 315 V and 500 V DC, respectively.

VVG 4x4ok-1 is a power flat cable, with a copper core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz. For laying without limiting the level difference along the laying route, including on vertical sections.

AVVGng-3x10ok - 0.66 is a power cable - 3 by 10 mm2, with an aluminum core, insulation and a PVC shell of reduced fire hazard.The cables are designed for transmission and distribution of electric power and electrical signals in stationary installations at a nominal alternating voltage of 660 V and 1000 V of a nominal frequency of 50 Hz or at a constant voltage of 1000 V and 1500 V, respectively.

KVBBSHVNG(A) 14x1.0 is an abbreviated marking of an armored control cable with 14 copper cores with a cross section of 1.0 square millimeters, insulated and sheathed in polyvinyl chloride plastic of reduced fire hazard with low smoke emission. The armored non-combustible control cable is designed for stationary connection to electrical devices with a voltage of up to 660 Volts of alternating current with a frequency of up to 100 Hertz.

AVVGng(A)-3x50ms+1x25ms(N, PE) - 1 is a power cable with an aluminum core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz

VVGng(A)-LS 1x2.5ok-0.66 is a power flat cable, with a copper core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz. For laying without limiting the level difference along the laying route, including on vertical sections.

Signal-blocking cables are designed for electrical alarm systems, centralization and blocking, fire alarm and automation. They are used for single laying in rooms, dry channels and tunnels, in an aggressive environment in the absence of mechanical influences on the cable.

The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz

AVVG 3x4 - 0.66 is a power cable - 3 by 4 mm2, with an aluminum core, insulation and a PVC shell of reduced fire hazard.The cables are designed for transmission and distribution of electric power and electrical signals in stationary installations at a nominal alternating voltage of 660 V and 1000 V of a nominal frequency of 50 Hz or at a constant voltage of 1000 V and 1500 V, respectively.

SIP-4 4x50 - 0.6/1- this is a self-supporting insulated wire (Type-4) - 4 by 35 mm2, with aluminum cores covered with insulation made of light-stabilized cross-linked polyethylene.This wire is intended for branches from main power transmission lines to the input and for laying along the walls of buildings and engineering structures at a nominal voltage of up to 1000 Volts inclusive.

VVG-Apg(A) 2x6ok-1 is a power flat cable, with a copper core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz. For laying without limiting the level difference along the laying route, including on vertical sections.

AVVG 5x4ok - 1 is a power cable with 5 aluminum cores with a cross section of 4 square millimeters, insulated and sheathed in polyvinyl chloride plastic of reduced fire hazard with low smoke emission.This cable is designed for stationary installation in power grids with a rated voltage of up to 1000 Volts, a frequency of 50 Hertz and a current load of up to 30 amperes.

The cable is designed for operation in subscriber access networks in the frequency range up to 2048 kHz and the organization of lines on distribution telecommunication networks from the terminal device to the subscriber and sealing by transmission systems with a rated voltage of remote power supply up to 225 V or 350 V AC with a frequency of 50 Hz, or voltage up to 315 V and 500 V DC, respectively.

The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz

AVVGng-LS 3x35mk - 1 is a power cable - 3 by 35 mm2, with an aluminum core, insulation and a PVC shell of reduced fire hazard.The cables are designed for transmission and distribution of electric power and electrical signals in stationary installations at a nominal alternating voltage of 660 V and 1000 V of a nominal frequency of 50 Hz or at a constant voltage of 1000 V and 1500 V, respectively.

AVVG 3x25mk - 0.66 is a power cable - 3 by 25 mm2, with an aluminum core, insulation and a PVC shell of reduced fire hazard.The cables are designed for transmission and distribution of electric power and electrical signals in stationary installations at a nominal alternating voltage of 660 V and 1000 V of a nominal frequency of 50 Hz or at a constant voltage of 1000 V and 1500 V, respectively.

VVG 3x2.5ok - 0,66 - 1 - this is a power flat cable, with a copper core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz. For laying without limiting the level difference along the laying route, including on vertical sections.

KSPVEng-LS 2x0.8 is a cable for alarm systems, communications and telecommunications with 2 single-wire copper cores, 0.8 mm2 in section, insulated and sheathed in non-combustible PVC plastic with reduced smoke emission. This cable is used for stationary installation in alarm systems, data transmission, telecommunications, with an operating voltage of up to 250 volts.

AVVGng(A)-3x35mk+1x16ok(N,PE) - 0.66 is a power cable with an aluminum core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz

AVVG 3x95ms+1x35ms - 1 is a power cable, with an aluminum core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz.

AVVG(A)NG-LS 1x4mk is a power cable - 1 by 4 mm2, with an aluminum core, insulation and a PVC shell of reduced fire hazard. The cables are designed for transmission and distribution of electricity in stationary electrical installations at a nominal alternating voltage of 0.66 and 1 kV with a nominal frequency of 50 Hz